2–3 mm
Gap all round, inset doors
15–25%
Door cost premium, inset
2×
Installation time, inset vs overlay
2
Planes of hinge adjustment needed
90°
Minimum opening for a pull-out behind
Short answer

Overlay for almost everything: cheaper, forgiving, and it does not need a frame. Inset where the design intent is a flush plane — heritage work, panelled rooms, high-end residential — and where the budget covers both the door premium and the installation time.

Key takeaways
  • Inset means the door sits inside the opening, flush with the frame face. Overlay means it covers the frame or carcass edge from the front.

  • Inset needs a frame. You cannot inset into a true frameless carcass without building a planted front.

  • The working gap is 2–3 mm on all four sides. Less and the door binds as the frame moves; more and the shadow line looks like an error.

  • Expect 15–25% more on door cost and roughly twice the installation time. The installation is the hidden number.

  • In a humid or unheated building, solid timber inset doors move enough to bind seasonally. Overlay is more forgiving.

1. The difference in one line

An overlay door stands in front of the cabinet face. An inset door sits inside the opening, so the door face and the frame face are the same plane.

Everything else follows from that. Overlay has a shadow line where the door meets its neighbour. Inset has a gap on all four sides, and that gap is the design feature — which is why it has to be even.

Inset against overlay
PropertyInsetOverlay
Door positionFlush inside the frameCovers the frame or edge
Needs a frameYesNo
Typical gap2–3 mm all round3 mm reveal between doors
Relative door cost+15–25%Baseline
Installation timeAbout 2×Baseline
Tolerance for movementLowHigh

2. What inset demands from the box

Three things have to be true before an inset door closes properly: the opening is square, the door is machined to the actual opening rather than a nominal size, and the hinge adjusts in two planes without visible slots.

That is why inset is a system, not a door upgrade. A carcass that is 2 mm out of square will show as a tapering gap, and no hinge adjustment hides a taper. On a framed cabinet the frame is machined after assembly for exactly this reason.

3. Where the cost actually goes

The door premium is visible on the quote: 15–25% above overlay, because the door is made to the opening and the frame needs a second machining pass.

The installation is not on the quote. An experienced fitter will set eight inset doors in the time it takes to set twenty overlay ones, because every gap is adjusted individually and every door is checked against its neighbours. On a 30-door kitchen, that is two extra days.

Cost build-up on a 30-door kitchen
ItemOverlayInset
Door costBaseline+15–25%
Frame machiningNot applicableExtra pass per opening
Install days24
SnaggingLowHigher — gaps are visible
Damaged door replacementStandard sizeMade to the opening

4. Where inset earns its money

High-end residential and heritage work, where the flush plane is the point. A run of inset doors with even gaps reads as furniture rather than joinery, and that is what the client is paying for.

It also suits panelled rooms. In a room with applied mouldings, a projecting overlay door looks pasted onto the wall; an inset door continues the plane.

Specifying inset doors on a project?
Send the elevations — we will mark the gaps and hinge positions before the drawings are frozen.

5. Where inset is a mistake

Humid or unheated buildings. Solid timber moves seasonally; a 2 mm gap in the dry season becomes 0.5 mm in the wet one, and the door binds. Overlay absorbs the same movement without contact.

And budget-driven jobs with tight programmes. If the fitter is being pushed, the gaps will be uneven, and uneven gaps on inset doors are the most visible defect in the whole kitchen.

Choose by situation
SituationBetter choiceWhy
New-build apartment kitchenOverlayCost and speed
Heritage or panelled roomInsetFlush plane is the point
Humid or unheated buildingOverlayTimber movement
Tight programmeOverlayHalf the install time
High-end villa, fixed budgetInset if gaps can be setLook, not durability

Frequently asked questions

How big should the gap be around an inset door?

2–3 mm on all four sides. Below 2 mm the door binds when the frame moves; above 3 mm the shadow line looks like a mistake.

Can inset doors be used on frameless cabinets?

Not truly. You need a frame or a planted front. Some makers build a frameless box with a machined front panel, which is inset in appearance only.

Why are inset doors more expensive?

The door is machined to the actual opening, the frame needs a second pass, and installation takes roughly twice as long.

Do inset doors need special hinges?

Yes — two-plane adjustment and a low-profile cup, so the door can be set flush without visible slots. Standard overlay hinges do not have the range.

Is inset better quality?

It is more demanding, not better. A well-built overlay kitchen with even reveals outperforms a badly set inset one on every measure except the look the client asked for.

BFP
BFP Project Team
Cabinetry manufacturing & export · since 2016

This guide is based on live project files: specification reviews, pre-shipment inspection reports and clearance documents from apartment, townhouse and villa work. Where a figure varies by project we give the range rather than a single number. Standards and duty treatment should be confirmed against the current version and your own customs broker.

  Send floor plans and unit count — drawings and per-unit price back within 24 hours.
On this page
Get a project proposal
Send your floor plans and unit count — we reply with shop drawings and a per-unit quote.
Reply within 24 hours by email.
Key facts at a glance
Gap2–3 mm all round
Door cost+15–25% over overlay
Install timeAbout 2× overlay
FrameRequired for true inset
Best forHeritage, panelled rooms, high-end
Related Project Cases
All projects →
Product categories
All categories →


×

Contact Us

Full Name *
Business Email *
WhatsApp / Phone (Fast Response)
Project Type (Optional)
Estimated Units / Quantity (Optional)
Project Details / Message *

This website utilizes cookies.

We employ cookies to analyze website traffic and enhance your browsing experience. Data securely aggregated, privacy protected. See Privacy Policy for details.

I agree