4
Common finishes
2–3
Coats of lacquer
0.6–1.0 mm
HPL thickness
3–5 mm
Veneer face
2
Repairable finishes
Short answer

Lacquer gives the best depth and can be repaired; melamine is the most durable for the price; veneer gives real grain; thermofoil suits profiles and tight budgets but is heat-sensitive. Heat and moisture decide more than wear. The finish that survives a busy kitchen is not always the hardest one.

Key takeaways
  • Lacquer: deep colour, repairable, slower to produce.

  • Melamine: durable and economical, limited repair.

  • Veneer: real grain, needs a stable core.

  • Thermofoil: suits profiles, fails near heat.

  • Compare the system and edge treatment, not just the price.

1. The four finishes

Lacquer is a sprayed coating, usually two or three coats. Melamine is a resin-impregnated paper pressed onto the board. Veneer is a thin layer of real wood. Thermofoil is a PVC film vacuum-formed over a profiled door. Each has a different failure mode.

2. Comparison

PropertyLacquerMelamineVeneerThermofoil
DurabilityGoodVery goodGoodGood
HeatGoodGoodGoodPoor
RepairSandableLimitedPatchablePoor
CostHighLowMedium–highLow
Lead timeLongerShorterMediumShorter

The table is directional. The actual performance depends on the system, the substrate and the edge treatment, which is why the specification matters more than the category.

3. Heat and moisture

Heat is the main failure mode for thermofoil and a risk for thin lacquer. Moisture is the main risk for melamine edges and for veneer on an unstable core. A door near an oven, a kettle or a shower needs a finish specified for that environment, not just a durable one.

4. Repair

Lacquer and veneer can be sanded or patched; melamine and thermofoil are harder to repair invisibly. In a rental or a hotel, repairability matters more than the initial hardness, because the door will be damaged and the question is whether it can be fixed in place.

5. Cost and lead time

Lacquer is the most expensive and the slowest, because it needs multiple coats and curing. Melamine is the cheapest and fastest. Veneer sits in the middle. Thermofoil is inexpensive but limited by heat. The carcass guide covers the board behind the finish.

6. Choosing a finish

Start with the room: a busy kitchen needs heat and wear resistance; a bathroom needs moisture resistance; a bedroom can take a softer finish. Then check the design: profiles need thermofoil or lacquer; flat doors suit melamine or veneer. The door styles guide covers the profiles.

7. Specifying a finish

Name the system, the number of coats or the film thickness, the sheen and the edge treatment. A specification that says painted without a system is not checkable. Ask for a sample door, not a chip, because the edge and the sheen show the difference.

8. Common mistakes

Three mistakes recur: choosing the hardest finish for a hot zone, comparing prices without comparing systems, and ignoring the edge treatment. Each is visible at specification stage and expensive at handover.

9. A checklist before you commit

Before you sign, confirm six things: the board grade, the hardware model, the finish system, the packing standard, the inspection scope and the payment schedule. Each should be in writing, not in a call. The quote checklist turns the six into a one-page comparison.

10. Common mistakes

The most common mistake is comparing a factory price with a landed cost. The second is leaving the inspection out of the budget. The third is paying the balance before the inspection is signed off. Each is avoidable with a written scope and a pre-shipment inspection.

11. How to measure the room

Measure each wall at three points, top, middle and bottom, and use the smallest. Walls are rarely square, and a 10 mm bow over three metres changes the filler. Measure the ceiling at each corner and note sockets, radiators and soil pipes before drawing. A measured survey saves more time than a faster drawing, and the measuring guide has a printable sheet.

13. A specification checklist

Write four lines for every material: the product, the grade, the thickness and the surface or edge treatment. A material specified by name alone leaves the grade to the factory, and the grade is where the cost and the performance sit.

14. Questions the factory will ask

Expect four questions: which grade, which thickness, which edge and which batch. The answers should already be in the specification. If they are not, the factory will choose, and the choice will be the cheapest that meets the drawing.

Choosing a door finish for a project?
Send us the room types and design intent and we will recommend a finish system with a sample schedule.
Request a finish schedule

Frequently asked questions

Which door finish is most durable?

Melamine and HPL resist wear well for the price. Lacquer looks better and can be repaired, but it is softer. Thermofoil resists wear but is sensitive to heat.

Is lacquer worth the extra cost?

For visible, design-led kitchens, often yes: it gives depth and can be repaired. For rental or volume work, melamine is usually the better value.

Can veneer doors be repaired?

Small chips can be patched; deep damage is harder to hide. Solid wood edges help, because the edge can be sanded.

Why does thermofoil fail?

Heat. A thermofoil door near an oven or a kettle can lift at the edge, and the film cannot be re-bonded invisibly.

Which finish is best for a bathroom?

A moisture-resistant system: compact laminate, or a well-sealed melamine or lacquer. Avoid thermofoil in a steamy room.

How do I compare finish quotes?

Compare the system, the number of coats or the film thickness, the edge treatment and the warranty. A price without the system is not comparable.

BFP
BFP Project Team
Cabinetry manufacturing & export · since 2016

This guide is based on live project files: specification reviews, pre-shipment inspection reports and clearance documents from apartment, townhouse and villa work. Where a figure varies by project we give the range rather than a single number. Standards and duty treatment should be confirmed against the current version and your own customs broker.

  Send floor plans and unit count — drawings and per-unit price back within 24 hours.
On this page
Get a project proposal
Send your floor plans and unit count — we reply with shop drawings and a per-unit quote.
Reply within 24 hours by email.
Key facts at a glance
LacquerDeep colour, repairable, slower
MelamineDurable, economical, limited repair
VeneerReal grain, needs stable core
ThermofoilProfiles and tight budgets, heat-sensitive
RepairLacquer and veneer sandable
Best forLacquer premium, melamine volume, veneer design
Related Project Cases
All projects →
Product categories
All categories →


×

Contact Us

Full Name *
Business Email *
WhatsApp / Phone (Fast Response)
Project Type (Optional)
Estimated Units / Quantity (Optional)
Project Details / Message *

This website utilizes cookies.

We employ cookies to analyze website traffic and enhance your browsing experience. Data securely aggregated, privacy protected. See Privacy Policy for details.

I agree